83,13 € tax incl.
97,80 €
-15%
0
Direct factory!
Sold in pairs.
Thickness in mm (coating): 8 mm
total width by axles: 16 mm
Distance between centers: 100x4
Moyeu Diameter (Alsage): 57 mm
Fastening thread: M12x1.5
Colori des cales : Anodized black
Screws not included
Without rim centerer
Fixing system: Simple bolts
Screw mounting system
Type of system Eibach 1:
kit reference : S90-1-08-003-B
Example of compatible vehicles:
AUDI COUPÉ (81, 85) 06.86 - 12.96
AUDI 82 (8C, B4) 09.91 - 12.94
AUDI 82 AVANT (8C, B4) / 80 STATION WAGON (8C, B4) 09.91 - 01.96
AUDI CABRIOLET (8G7, B4) / CONVERTIBLE (TYP 89) 05.91 - 08.00
BMW 3 (E30) / 3 (E30) 09.82 - 03.92
BMW 3 TOURING (E30) / 3 STATION WAGON (E30) 07.87 - 10.94
BMW 3 CABRIOLET (E30) / 3 CONVERTIBLE (E30) 12.85 - 10.93
SEAT AROSA (6H) 05.97 - 06.04
SEAT CORDOBA (6K1/6K2) 02.93 - 10.99
SEAT CORDOBA VARIO (6K5) / CORDOBA STATION WAGON (6K5) 08.96 - 06.99
SEAT IBIZA II (6K1) 03.93 - 08.99
SEAT IBIZA II (6K1) 08.99 - 02.02
VW GOLF II (19E, 1G1) 08.83 - 12.92
VW GOLF III (1H1) 08.91 - 07.98
VW GOLF III VARIANT (1H5) / GOLF III STATION WAGON (1H5) 07.93 - 04.99
VW GOLF III CABRIOLET (1E7) / GOLF III CONVERTIBLE (1E7) 07.93 - 05.98
VW GOLF IV CABRIOLET (1E7) / GOLF IV CONVERTIBLE (1E7) 06.98 - 06.02
VW LUPO (6X1, 6E1) 09.98 - 07.05
VW PASSAT (3A2, 35I) 02.88 - 12.97
VW PASSAT VARIANT (3A5, 35I) / WAGON STATION PASSAT (3A5, 35I) 02.88 - 06.97
VW POLO (6N1) 10.94 - 10.99
VW POLO (6N2) 10.99 - 10.01
VW POLO KASTEN (6NF) / POLO BOX (6NF) 09.94 - 12.99
VW POLO CLASSIC (6KV2) 11.95 - 07.06
VW POLO VARIANT (6KV5) 09.97 - 09.01
VW VENTO (1H2) 11.91 - 09.98
Be careful to take this technical information into account before ordering! In case of doubt, our team remains at your disposal to refine your research!
Technical Notes: Use only on the front axle on some models, as the centre of the rear axle is too long. Useable up to 16mm high collar! From production 161225 - Equally suitable for VW UP!, Seat MII, rear axle Skoda Citigo, since the maximum height of the usable clamp has increased to 17 mm! (Note the relief on the intertoise!)
A question about compatibility, fixing your hold? Need to find the right visserie? Contact us
Additional note:
For users of Rumble Bars, threaded combos, short springs, or low suspensions, wheel chock mounting may be required. Spring lowering is always given on a standard chassis basis. If you have a sport chassis option, the lowering of this one will be deducted. The same goes for special equipment (4x4, leather, 3 doors, auto gearbox...etc...) the lowering can sometimes vary by a few millimeters because of the extra weight. The lowerings are never perfectly identical to the millimeter, no need to go looking for the detail with the caliper, of course.
Reminder: If your vehicle is equipped with wheel studs, measure the length of your studs before ordering. If you use thin wheel studs, the studs will protrude and prevent the installation of the rim. It will then be necessary to buy studs with a suitable length under the head because they are not supplied with the chocks.
Find our Antivols de roues, goujons longs, visseries de jantes in the dedicated section!
Materials: | Aluminium |
Filter the type of parts | Wheels: Wheels (all models combined) |
Filter the type of parts | Wheels: Single bolts (8mm) |
Thickness: | 8mm |
Colors: | Black anodized |
Wheel | Spacers |
Options de roues | Simple boulonnerie |
Ref: S90-2-16-011-B
Ref: S90-1-05-032
Ref: S90-2-14-002
Ref: S90-1-07-006
Ref: S90-2-15-005
Ref: S90-2-20-004
Ref: S90-7-25-003
Ref: S90-2-12-013
Ref: S90-7-20-028
Ref: S90-2-10-034
Ref: S90-2-10-027
Ref: S90-2-10-027-B
Ref: S90-2-12-003
Ref: S90-2-15-013
Ref: S90-2-20-003
Ref: S90-2-12-003-B
Ref: S90-2-15-013-B
Ref: S90-2-20-003-B
Ref: S90-2-08-003
Ref: S90-2-08-003-B
Ref: S90-2-22-001
Ref: S90-2-22-001-B
Ref: S90-1-05-006
Ref: S90-1-08-001
Ref: S90-7-20-017
Ref: S90-7-25-005
Ref: S90-7-30-012
Ref: S90-7-20-017-B
Ref: S90-7-25-005-B
Ref: S90-1-05-016