Français
English GB
Porsche 911 (992) 3.7T (Turbo) (580 hp) remapping
- Fuel
- Petrol
- Years
- since 2019
- ECU
- Bosch MG1CP007
- Method
- Through the OBD port
Stage 1
Porsche 911 (992) 3.7T (Turbo) (580 hp)
Power
+120 hp +21 %
Torque
+150 Nm +20 %
| Power | Torque | |
|---|---|---|
| Stock | 580 hp | 750 Nm |
| Stage 1 | 700 hp | 900 Nm |
| Gain | +120 hp | +150 Nm |
E85 FlexFuel conversion
Porsche 911 (992) 3.7T (Turbo) (580 hp)
Power
Torque
| Power | Torque | |
|---|---|---|
| Stock | 580 hp | 750 Nm |
The E85 figures for this engine are not published yet. The conversion lets you run on E85 bioethanol; a question before ordering? Contact us
How the remap works
- You order for your vehicle Engine and VIN: the map is prepared for your ECU.
- You receive the REPROG dongle A Bluetooth box that plugs into the OBD port under the dashboard.
- The app saves the stock map With MyFlasher (iOS, Android), the dongle reads and keeps the factory map.
- You flash in a few minutes The Dynaparts map is loaded; going back to stock remains possible at any time.
Other 911 (992) engines
| Engine | Stock | After remap | Gain | Details |
|---|---|---|---|---|
| 3.0T (385 hp) Petrol E85 compatible | 385 hp450 Nm | 485 hp650 Nm | +100 hp+200 Nm | |
| 3.0T (394 hp) Petrol E85 compatible | 394 hp | on request | ||
| 3.0T (S) (450 hp) Petrol E85 compatible | 450 hp530 Nm | 500 hp650 Nm | +50 hp+120 Nm | |
| 3.0T (GTS) (480 hp) Petrol E85 compatible | 480 hp550 Nm | 530 hp650 Nm | +50 hp+100 Nm | |
| 4.0 DFI GT3 (510 hp) Petrol E85 compatible | 510 hp470 Nm | 530 hp500 Nm | +20 hp+30 Nm | |
| 4.0 DFI GT3 RS (525 hp) Petrol E85 compatible | 525 hp465 Nm | 550 hp495 Nm | +25 hp+30 Nm | |
| 3.7 (Turbo) (550 hp) Petrol E85 compatible | 550 hp600 Nm | 700 hp900 Nm | +150 hp+300 Nm | |
| 3.7T (Turbo) (580 hp) Petrol E85 compatible | 580 hp750 Nm | 700 hp900 Nm | +120 hp+150 Nm | This page |
| 3.7T (Turbo S) (650 hp) Petrol E85 compatible | 650 hp800 Nm | 700 hp900 Nm | +50 hp+100 Nm |
All 911 (992) engines Parts compatible with this vehicle
Frequently asked questions
How does a remap with the REPROG pack work?
You plug the REPROG by Dynaparts Bluetooth OBD dongle into the vehicle's OBD port and install the MyFlasher app (iOS or Android). The dongle reads and saves the stock map, then loads the Dynaparts map for your engine. Flashing takes a few minutes, with no dismantling.
Why give my vehicle's VIN?
The map is prepared for your engine and ECU. The VIN (field E of the registration document) lets us check the exact vehicle version before shipping.
Can I go back to the stock map?
Yes. The stock map is saved during the first read and can be restored at any time from the app, in a few minutes.
What is the difference between Stage 1 and the E85 pack?
Stage 1 optimises injection, ignition and boost management on the original fuel. The E85 pack installs a FlexFuel map to run on E85 bioethanol, cheaper at the pump, without an add-on box.
Are the stated gains guaranteed?
Indicative figures measured on a well-maintained stock vehicle: they may vary with engine condition, fuel and measuring conditions. A remap changes the vehicle's characteristics: remember to inform your insurer.
Indicative figures measured on a well-maintained stock vehicle: they may vary with engine condition, fuel and measuring conditions. A remap changes the vehicle's characteristics: remember to inform your insurer.