Français
English GB
Skoda Octavia III (5E) 2.0 TFSI OPF (190 hp) remapping
- Fuel
- Petrol
- Years
- 2012 - 2020
- ECU
- Bosch MG1CS001 / Bosch MG1CS111
- Method
- Through the OBD port
Stage 1
Skoda Octavia III (5E) 2.0 TFSI OPF (190 hp)
Power
+50 hp +26 %
Torque
+100 Nm +31 %
| Power | Torque | |
|---|---|---|
| Stock | 190 hp | 320 Nm |
| Stage 1 | 240 hp | 420 Nm |
| Gain | +50 hp | +100 Nm |
E85 FlexFuel conversion
Skoda Octavia III (5E) 2.0 TFSI OPF (190 hp)
Power
+50 hp +26 %
Torque
+100 Nm +31 %
| Power | Torque | |
|---|---|---|
| Stock | 190 hp | 320 Nm |
| E85 | 240 hp | 420 Nm |
| Gain | +50 hp | +100 Nm |
How the remap works
- You order for your vehicle Engine and VIN: the map is prepared for your ECU.
- You receive the REPROG dongle A Bluetooth box that plugs into the OBD port under the dashboard.
- The app saves the stock map With MyFlasher (iOS, Android), the dongle reads and keeps the factory map.
- You flash in a few minutes The Dynaparts map is loaded; going back to stock remains possible at any time.
Other Octavia III (5E) engines
| Engine | Stock | After remap | Gain | Details |
|---|---|---|---|---|
| 1.5 TSI (130 hp) Petrol E85 compatible | 130 hp200 Nm | 175 hp300 Nm | +45 hp+100 Nm | |
| 1.5 TSI (150 hp) Petrol E85 compatible | 150 hp250 Nm | 175 hp300 Nm | +25 hp+50 Nm | |
| 1.8 TSI (179 hp) Petrol E85 compatible | 180 hp250 Nm | 220 hp320 Nm | +40 hp+70 Nm | |
| 2.0 TFSI OPF (190 hp) Petrol E85 compatible | 190 hp320 Nm | 240 hp420 Nm | +50 hp+100 Nm | This page |
| 2.0 TFSI RS (220 hp) Petrol E85 compatible | 220 hp350 Nm | 260 hp420 Nm | +40 hp+70 Nm | |
| 2.0 TFSI RS (230 hp) Petrol E85 compatible | 230 hp350 Nm | 300 hp440 Nm | +70 hp+90 Nm | |
| 2.0 TSI (245 hp) Petrol E85 compatible | 245 hp370 Nm | 305 hp430 Nm | +60 hp+60 Nm | |
| 2.0 TDI (150 hp) Diesel | 150 hp320 Nm | 185 hp420 Nm | +35 hp+100 Nm |
All Octavia III (5E) engines Parts compatible with this vehicle
Frequently asked questions
How does a remap with the REPROG pack work?
You plug the REPROG by Dynaparts Bluetooth OBD dongle into the vehicle's OBD port and install the MyFlasher app (iOS or Android). The dongle reads and saves the stock map, then loads the Dynaparts map for your engine. Flashing takes a few minutes, with no dismantling.
Why give my vehicle's VIN?
The map is prepared for your engine and ECU. The VIN (field E of the registration document) lets us check the exact vehicle version before shipping.
Can I go back to the stock map?
Yes. The stock map is saved during the first read and can be restored at any time from the app, in a few minutes.
What is the difference between Stage 1 and the E85 pack?
Stage 1 optimises injection, ignition and boost management on the original fuel. The E85 pack installs a FlexFuel map to run on E85 bioethanol, cheaper at the pump, without an add-on box.
Are the stated gains guaranteed?
Indicative figures measured on a well-maintained stock vehicle: they may vary with engine condition, fuel and measuring conditions. A remap changes the vehicle's characteristics: remember to inform your insurer.
Indicative figures measured on a well-maintained stock vehicle: they may vary with engine condition, fuel and measuring conditions. A remap changes the vehicle's characteristics: remember to inform your insurer.