EGR blanking plate 2.0 DCI

EGR delete for Renault, Nissan and Opel 2.0 dCi engines

This laser-cut 304 stainless steel plate, made in France, blocks the exhaust gas recirculated by the EGR valve. The result: a cleaner air/fuel mixture, better intake breathing, more torque and less carbon build-up. Stainless steel does not rust or warp with heat, so the plate stays sealed over time.

Warning light: yes, a remap is required

On this valve, the plate stops the flap from opening. The ECU detects it: the engine warning light comes on (EGR fault) and the engine may enter limp mode. There is no drilled version for this reference: a remap disabling the EGR function is required, to be planned before or right after fitting.

Compatible vehicles

Fits the 2.0 dCi diesel engine (M9R family), 90 to 178 hp, found in:

• Renault: Laguna II (hatchback, Grandtour), Laguna III (hatchback, Grandtour, Coupé), Mégane II (3/5-door, saloon, estate, coupé-cabriolet), Scénic II and Grand Scénic II, Espace IV, Koleos I, Vel Satis, Trafic II (van, bus, platform)
• Nissan: Qashqai I and Qashqai+2 (J10), X-Trail (T31), Primastar (X83)
• Opel: Vivaro A (X83) 2.0 CDTI

Not compatible with Mégane III, Scénic III and Mégane CC 2.0 dCi, which use a different valve.

How do I check my EGR valve matches?

This plate is designed for the 2.0 dCi electric EGR valve with a D-shaped 5-pin connector, as shown in the product photo. Before ordering, compare your valve with our photos, or email us a photo of your engine: the same model may have different valve generations depending on the year.

OE numbers and EGR valve equivalents

To make sure you order the right plate, compare your EGR valve part number with the numbers below.

• Renault: 8200327004, 8200327011, 8200691292, 8200693739, 8200797706, 8200797707
• Nissan: 14956-00Q0B, 14956-00Q0F, 14956-00Q0J, 14956-00Q1A
• Opel: 4431099, 4432905, 4433837, 4434941, 850785, 93161578, 93198005, 93198182, 93198436, 95515266

This valve is also sold under the aftermarket references JP Group 4319900400, BorgWarner (Wahler) 710939D, Valeo 703218, Magneti Marelli 571822112043, Ridex 1145E0053, NRF 48640, Nissens 98261, DRI 717730070 and Fast FT60206.

Why block off the EGR valve?

The EGR valve feeds part of the exhaust gas back into the intake to reduce nitrogen oxide emissions. The problem: on the 2.0 dCi it clogs with carbon, especially in town driving. Common symptoms: warning light, P0400 / P0403 / P0409 codes, hesitation, black smoke, unstable idle. Cleaning often lasts only a few thousand kilometres. Blocking it off improves engine efficiency and available torque, with no more recurring failures.

Fitting

The fitting direction is shown on the product photos: an arrow or drawing acts as instructions. Remove the valve, insert the plate, refit to factory torque. Take the opportunity to clean the intake pipe, often heavily clogged on these engines. Simple fitting, to be completed with an ECU remap.

Box contents

• 1 EGR delete plate in laser-cut 304 stainless steel, made in France

Reinforced gasket for EGR delete plates and engine silicone tube available separately as accessories, for a perfect seal.

Any questions or doubts about your engine? Our customer service replies quickly, photo in hand.